Baltos iR 2110

Industrial RISC PC with serial port, LAN, USB 2.0, microSD-Slot, Debian Linux

Baltos iR 2110 onRISC ARM Industrial PC with Ti Sitara Cortex-A8 Am3352 processor system on Chip SOC

	Features

	Specifications

	Ordering Information

	Drivers & Documentation

	Datasheet

	Inquiry this product

	View Larger Image

	BUY

The OnRISC Baltos iR 2110 is a fanless and DIN-Rail mounting suitable industrial embedded PC with very compact dimensions. It is based on an ARM Cortex-A8 with NEON SIMD Coprocessor, with up to 1GHz CPU clock speed. Low power consumption (3W typical), an extended temperature range (−20°C to 65°C), a wide power supply (12 — 50V DC) and an impressive MTBF (13 Years at 45°C) are qualities that make it an ideal system for industrial automation. iR 2110 is fully ESD and surge protected, complying with IEC 61000-4-2 (8KV air and 4KV contact).

IoT-Cloud Support

Thanks to it's rich connectivity Baltos devices can be used as IoT Gateways connecting sensors/actuators and arbitrary cloud providers like Amazon's AWS IoT, Microsoft's Azure IoT Hub and others using MQTT protocol directly or via the cloud providers own APIs.
Besides Baltos series can also serve as a controller. Both roles can be easily programmed using either traditional programming languages or Node-RED*, a visual flow-based programming for the Internet of Things.

Easy-to-use starter kits

Baltos embedded systems run several Linux flavored distributions on an ARM core as an operating system. In addition, two pre-packaged bootable SD cards are provided: The Debian GNU/Linux and an upstream OpenWrt image; the latter includes an install-option to the internal flash memory. A VPN router firmware specialized in easy-to-use VPN networking is also available (VPNRouter).

Booting options and BSPs

Baltos iR 2110 can be booted from either NAND flash or microSD card. The NAND flash is a robust boot medium capable of withstanding power cuts and vibrations. microSD cards have the advantage of providing arbitrarily large storage amounts. Buildroot, Yocto and OpenWrt BSPs provide a small footprint and would fit well into the NAND storage, whereas Debian is best used on the microSD card.

Rich connectivity

WLAN802.11b/g/n is available as a common option; furthermore, two locations for SMA-antenna sockets are provided. The balanced variety of interfaces such as LAN, USB, RS232/422/485 serial ports and microSDHC enable Baltos iR 2110 to act like a powerful gateway between networks, various industrial devices and field buses.

Secure Remote Access

For the Baltos series there is a software option that uses the viaVPN Cloud system (www.viaVPN.com), which can be remotely accessed and monitored over the Internet. viaVPN provides secure and strongly encrypted access, without the need for any reconfiguration of existing firewalls. In case a customer's firmware/application is accessible via Ethernet or Wifi — as for example via a web interface or Telnet/SSH connection — viaVPN extends the access over internet by a protected VPN tunnel.

Keywords: OnRISC SOC ARM Cortex-A8 Sitara Am335x RISC, openWRT

Base model is AM3352@600MHz, also usable as Router system operating openWRT or OEM software

Features
ARM AM3352 Cortex-A8 @ 600MHz 256MB DDR3 / 256MB NAND 1 x microSD-Slot 2 x LAN (1 Gigabit, 1 Fast Ethernet) 1 x WLAN 802.11b/g/n (optional) 1 x USB 2.0 Host 1 x RS232/422/485 Low Power, fanless, safe connectors ESD surge protection Operating Temperature −20°C - 65°C BSPs: Debian, OpenWrt, Buildroot, Yocto
Back to Top
Specifications
Software Specifications
Linux	Debian: Latest stable release available as ready-to-run SD card image or can be built/customized via ELBE project (Github) Buildroot: BSP with Kernel and bootloader patches and basic configuration (Github) Yocto: layer-baltos with Kernel and bootloder patches suitable for new projects or integration into already available projects (Github) Buildroot and Yocto are suitable for installation to NAND Flash
OpenWrt	Based on branch DD 'Designated Driver', comes ready-to-use on a microSD card. Installation into NAND Flash memory is supported. To self-create this software the setup procedure is on GitHub.
Remote Access (option)	The daemon to access the viaVPN system provides secure Remote Access over Internet. It supports a Debian-based Installation, and Buildroot as well. Connect via Internet viaVPN provides easy access to remotely installed systems. Software installation is quickly done with convenient tools to get access from everywhere. Security All communication uses a VPN-tunnel encrypted by SSL/TLS and AES-256. Firewall friendly, ready for 3G/4G use viaVPN Cloud Server access uses common web ports. Reconfiguration of firewalls is not required. This enables the use with mobile networks.
Back to Top
System
Hardware	Sitara AM3352 ARM Cortex-A8 RISC CPU @ 600MHz 256MB DDR3 Real time clock with battery backup
Mass Storage	256MB NAND Flash memory (bootable) SD 2.0 / SDHC microSD-card slot (bootable)
Network	1x 1000/100/10 Mbps Gigabit Ethernet 1x 100/10 Mbps Fast Ethernet
Serial Peripherals	1x USB 2.0 Host 1x RS232/422/485 high speed
LED	1x Power, 1x WLAN, 1x Application LAN: 2x Link and Speed COM: TxD and RxD
DIP Switch	4 x switches for user's application
Back to Top
Serial Ports
No. of Ports/Type	1 × RS232/422/485 selected by software Highspeed UART, 64 Byte FIFO (16C750)
Connector	DB-9 male
Protection	16kV ESD surge protection
Operating Modes	RS232 RS422 full duplex (120Ω on/off) RS485 4 wire, full duplex (120Ω on/off) RS485 2 wire, half duplex (120Ω on/off)
Configuration	Software sets operating mode and RS422/485 termination No High/Low biasing resistors needed
Signals	RS232: TxD,RxD, RTS,CTS, DTR,DSR, DCD, RI, GND RS422: Tx+/-, Rx+/-, GND RS485 4 wire: Tx+/-, Rx+/-, GND RS485 2 wire: Data+/-, GND
RS485 Data Direction control	Driver Automatic via RTS
Data bits	5, 6, 7, 8
Stop bits	1, 2
Parity	None, Even, Odd, Mark, Space
Flow Control	RTS/CTS, XON/XOFF
Baudrate	RS232: 200 bps to 921.6/1000 kbps RS422/485: 200 bps to 3.7Mbps Supports non-standard baudrates
Back to Top
Wireless interface (option)
Standards	2.4GHz Radio, supports IEEE Std. 802.11b/g/n
WLAN Modes	Access Point (AP) or Client (Station)
TX Power	802.11b: Typ. 15.5dBm ±1.5 dBm @ 1Mbps (DSSS) Typ. 15.5dBm ±1.5 dBm @ 11Mbps (OFDM) 802.11g: Typ. 15.6dBm ±1.5 dBm @ 6Mbps (CCK) Typ. 13.5dBm ±1.5 dBm @ 54Mbps (OFDM) 802.11n: Typ. 13.4dBm ±1.5 dBm @ 6.5Mbps (OFDM) Typ. 13.3dBm ±1.5 dBm @ 150 Mbps(OFDM)
RX Sensitivity	802.11b: -95.6dBm @ 1Mbps, -88dBm @ 11Mbps 802.11g: -91.3dBm @ 6Mbps, -74.2dBm @ 54 Mbps 802.11n: -88.8dBm @ 6.5Mbps (20 MHz), -72dBm @ 72.2Mbps (20 MHz)
Transmission Rate	802.11b: 11Mbps 802.11g: 6 to 54Mbps 802.11n: 6.5 to 150Mbps
Transmission Distance	Up to 100m in open areas
Wireless security	WEP WPA WPA2 WPA2-Enterprise (IEEE 802.1X/RADIUS)
Antenna Connector	RP (Reverse-Polarity) SMA
Back to Top
Power Requirements
Input Voltage	9 — 54V DC
Power Consumption	0.2A @ 12V minimal 0.3A @ 12V typical, plus devices on USB
Connector	3-pin Terminal Block
Back to Top
Housing and Mounting
Case	0.8mm sheet metal
Weight	w/o box 250g; w/h box 500g
Dimensions	115×73×25 mm³ (W×L×H)
Packaged	150×107×48 mm³
Mounting	DIN Rail (option) Wall mount (option)
Back to Top
Environmental Data
Operating Temp	−20°C — 65°C
Storage Temp	−30°C - 85°C
Ambient Humidity	10-85% non-condensing
Back to Top
Standards
Declarations	CE, FCC
Environment	RoHS
EMI	EN 55022 Class B EN 61000-3-2: Limits of harmonic current emissions EN 61000-3-3: Limitation of voltage changes 47 CFR FCC Part 15 Subpart B
EMS (EN 55024)	EN 61000-4-3: Radiated RFI EN 61000-4-4: Electrical Fast Transient EN 61000-4-5: Surge EN 61000-4-6: Induced RFI EN 61000-4-8: Power Frequency Magnetic Field EN 61000-4-11: Power supply dips
ESD	EN 61000-4-2 4kV contact 8kV air for Serial Port USB Ethernet DC Power connector
Back to Top
MTBF (Mean Time Between Failures)
MTBF	39.0 Years @ 25°C 13.0 Years @ 45°C
Standard	Telcordia (Bellcore) Standard; RelCalc. 5.0 BELL-7
Back to Top
Warranty
Warranty Period	2 years
Back to Top
Open Source Software
Licenses	This product uses open source software to fulfill part of its functions. Licenses for the open source software are granted under the GNU General Public License in various versions. For details about those see the information in the firmware download and visionsystems.de/opensource
Back to Top
Ordering Information
6833	OnRISC Baltos iR 2110
6840	OnRISC Baltos iR 2110 WLAN
Back to Top
Options
6031	Power adapter 110-230V AC to 12V @1A, DC, EU plug
6034	Power adapter 110-230V AC to 12V @1A, DC, US plug
6689	WLAN Kit internal internal module 802.11b/g/n, pigtail and antenna Purchase time option, not for later retrofitting
6692	DK-NCP DIN-Rail mounting kit
6693	WK-NCP Wallmount kit
6841	Daemon viaVPN, provides secure Remote Access system over Internet
6835	Starter Kit Debian 4GB SD card for DEBIAN/GNU Linux Power adapter 12V @ 1A USB Adapter cable for console port
6842	Starter Kit OpenWRT 4GB SD card for OpenWRT Power adapter 12V @ 1A USB Adapter cable for console port
Back to Top
Packaging
Packing list	OnRISC Baltos iR 2110 system Terminal block for Power Supply Reverse SMA Antenna (WLAN model only)
Back to Top

You can purchase VSCOM's products easily from a wide variety of leading technology distributors or partners. Please call us or contact us by mail to find the best ordering method for your needs.

* Specifications are subject to change without notice.
* All the trademarks and brands are property of their rightful owners.

About VSCOM | Impressum | Contact Us | Term & Conditions | Privacy Policy