| Features |
- Converts between Modbus/RTU, Modbus/ASCII and Modbus/TCP over Ethernet, WLAN or Internet
- LAN 10/100 Fast Ethernet
- Configuration over Web interface
- Supports Modbus Master Multiplexing
- Supports TCP/IP, DHCP, ICMP, HTTP, DNS
- RS232/422/485 interface selected by Software
- Optional: Wireless network IEEE 802.11b/g/n
|
 Back to Top |
| Specifications |
| Ethernet Interface |
Speed/Type |
100Mbps/10Mbps Auto-detecting |
Connector |
RJ45 (8P8C) 8 pin |
LEDs |
Power, WLAN, Ready, Ethernet Link / Speed |
| Back to Top |
| Serial Interface |
No. of Ports/Type |
1 × RS232/422/485 selected by software |
Connector |
DB-9 male |
Protection |
16kV ESD surge protection |
Operating Modes |
RS232
RS422 full duplex (120Ω on/off)
RS485 4 wire, full duplex (120Ω on/off)
RS485 2 wire, half duplex (120Ω on/off)
|
Configuration |
Software sets operating mode and RS422/485 termination
No High/Low biasing resistors needed |
Signals |
RS232: TxD,RxD, RTS,CTS, DTR,DSR, DCD, RI, GND
RS422: Tx+/-, Rx+/-, GND
RS485 4 wire: Tx+/-, Rx+/-, GND
RS485 2 wire: Data+/-, GND
|
RS485 Data Direction control |
ARTc (Automatic Receive Transmit control) |
Data bits |
7, 8 |
Stop bits |
1, 2 |
Parity |
None, Even, Odd |
Baudrate |
ModBus: up to 115.2 kbps
RS232: 200 bps to 921.6/1000 kbps (physical)
RS422/485: 200 bps to 3.7Mbps (physical) |
LEDs |
TxD/RxD for each port |
| Back to Top |
| Software |
Installation |
DIP switches set the device to DHCP or a defined fixed IP Address to be contacted via WEB Browser |
Operating mode |
- Promiscous Mode
- Messages received from the network are sent to the serial port, messages from the serial port are sent to the connected network host. (Circuit Switching)
- Direct Mapping Mode
- Received messages are scanned for their target address. This address is found in the mapping table, the message is sent to the defined connection. (Packet Switching)
|
Network Protocols |
Modbus/TCP, TCP/IP, DHCP, ICMP, HTTP, DNS, UDP, UPnP/SSDP |
Serial Protocols |
Modbus/RTU and Modbus/ASCII |
Modbus Master Multiplexing |
An extension to the standard. Slaves on serial lines may answer requests from multiple masters. The masters connect to ModGate Plus by Modbus/TCP. |
Configuration |
Configuration over WEB Browser |
Detection |
Announces presence in the network via Universal Plug and Play (UPNP) protocol |
DNS |
Domain Name Server support |
Firmware |
Firmware update over WEB Browser |
Security |
Webinterface is password protected. The password can be changed in the Webinterface. |
USB 2.0 |
for logging/debugging |
| Back to Top |
| Wireless interface (option) |
Standards |
2.4GHz Radio, supports IEEE Std. 802.11b/g/n |
WLAN Modes |
Access Point (AP) or Client (Station) |
TX Power |
- 802.11b:
- Typ. 15.5dBm ±1.5 dBm @ 1Mbps (DSSS)
- Typ. 15.5dBm ±1.5 dBm @ 11Mbps (OFDM)
- 802.11g:
- Typ. 15.6dBm ±1.5 dBm @ 6Mbps (CCK)
- Typ. 13.5dBm ±1.5 dBm @ 54Mbps (OFDM)
- 802.11n:
- Typ. 13.4dBm ±1.5 dBm @ 6.5Mbps (OFDM)
- Typ. 13.3dBm ±1.5 dBm @ 150 Mbps(OFDM)
|
RX Sensitivity |
- 802.11b:
- -95.6dBm @ 1Mbps, -88dBm @ 11Mbps
- 802.11g:
- -91.3dBm @ 6Mbps, -74.2dBm @ 54 Mbps
- 802.11n:
- -88.8dBm @ 6.5Mbps (20 MHz), -72dBm @ 72.2Mbps (20 MHz)
|
Transmission Rate |
802.11b: 11Mbps
802.11g: 6 to 54Mbps
802.11n: 6.5 to 150Mbps |
Transmission Distance |
Up to 100m in open areas |
Wireless security |
WEP
WPA
WPA2
WPA2-Enterprise (IEEE 802.1X/RADIUS)
|
Antenna Connector |
RP (Reverse-Polarity) SMA |
| Back to Top |
| Power Requirements |
Input Voltage |
9 - 54V DC |
Power Consumption |
0.25A @ 12V, 2.7W max |
Connector |
3-pin Terminal Block |
| Back to Top |
| Housing and Mounting |
Case |
0.8mm sheet metal |
Weight |
w/o box 0.25kg; w/h box 0.35kg |
Dimensions |
115×73×25 mm³ (W×L×H) |
Packaged |
150×107×48 mm³ |
Mounting |
DIN-Rail (optional)
Wall mount (optional)
|
| Back to Top |
| Environmental Data |
Operating Temp |
−20°C - 65°C |
Storage Temp |
−20°C – 85°C |
Ambient Humidity |
5-95% non condensing |
| Back to Top |
| Standards |
Declarations |
CE, FCC |
EMI |
EN 55022 Class B
EN 61000-3-2: Limits of harmonic current emissions
EN 61000-3-3: Limitation of voltage changes
47 CFR FCC Part 15 Subpart B
|
EMS (EN 55024) |
EN 61000-4-3: Radiated RFI
EN 61000-4-4: Electrical Fast Transient
EN 61000-4-5: Surge
EN 61000-4-6: Induced RFI
EN 61000-4-8: Power Frequency Magnetic Field
EN 61000-4-11: Power supply dips
|
ESD |
EN 61000-4-2 4kV contact 8kV air for
Serial Port
USB
Ethernet
DC Power connector
|
| Back to Top |
| MTBF (Mean Time Between Failures) |
MTBF |
41.5 Years @ 25°C
13.5 Years @ 45°C |
Standard |
Telcordia (Bellcore) Standard; RelCalc. 5.0 BELL-7 |
| Back to Top |
| Warranty |
Warranty Period |
2 years |
| Back to Top |
| Open Source Software |
Licenses |
This product uses open source software to fulfill part of its functions. Licenses for the open source software are granted under the GNU General Public License in various versions. For details about those see the information in the firmware download and visionsystems.de/opensource |
| Back to Top |
| Ordering Information |
6710 |
ModGate Plus 113 (1x RS232/422/485) |
| Back to Top |
| Options |
6031 |
Power supply adapter 12V DC, 1A |
6034 |
Power adapter 110-230V AC to 12V @1A, DC, US plug |
6689 |
WLAN Kit internal
internal module 802.11b/g/n, pigtail and antenna
Purchase time option, not for later retrofitting |
|
DK-NCP DIN-Rail mounting kit (clamp on rear side) |
|
WK-NCP Wallmount kit |
|
DSK-NCP DIN-Rail side mount kit (clamp on left side) |
|
DB9F-to-TB/5Pins for free wiring option |
|
DB9F-to-RJ45 for changing from DB9 to CAT5 wiring
(Optimised for RS422/485 operating modes) |
|
RJ45-to-DB9M for changing back from CAT5 to DB9 wiring
(Required to match the DB9 pinout at USB-COM Plus Mini) |
|
Serial Null-Modem adapter 9PF-9PF, change male to female |
| Back to Top |
| Packaging |
Packing list |
ModGate Plus 113
Terminal block for Power Supply
|
| Back to Top |
BUY 